Issues

• Eased setbacks: every corner of a rounded box eased by 4 is refused as not solid (the stitch glues a face curve's ends 5.66 mm apart)

  bugpriority: high
  tangency-labs/solidcore#1386 · Filter by author jyviko opened on Oct 28, 2026

• UV trims: an edge along a spline face's boundary row, parameterised differently, gets a trim at the wrong pace (5 mm off at its end)

  bugpriority: high
  tangency-labs/solidcore#1383 · Filter by author jyviko opened on Oct 28, 2026

• Setback blends: some section halves come back as polynomial splines off the round, not exact rational arcs

  bugpriority: high
  tangency-labs/solidcore#1377 · Filter by author jyviko opened on Oct 27, 2026
  1

• Setback blends: an ease length so rounds end curvature-continuous before their setback

  bugpriority: high
  tangency-labs/solidcore#1376 · Filter by author jyviko opened on Oct 27, 2026
  1

• SMLib: two tangent cylinders' boolean is unsound when multiply-adds are fused

  bugpriority: high
  tangency-labs/solidcore#1252 · Filter by author jyviko opened on Oct 27, 2026

• Triage: open issues already fixed on main (no closing keyword)

  tangency-labs/solidcore#1206 · Filter by author ablasik opened on Oct 26, 2026
  4

• SMLib: MakeFaceWithCurves reads an SmTArray<SmBSplineCurve*> as SmTArray<SmCurve*> (UBSan, shell path)

  bugpriority: high
  tangency-labs/solidcore#1180 · Filter by author jyviko opened on Oct 26, 2026

• SMLib: fillet post-process keeps edges and faces by stale pointer; the result depends on heap layout

  bugpriority: high
  tangency-labs/solidcore#1176 · Filter by author jyviko opened on Oct 26, 2026
  2

• SMLib: a fillet corner setback is measured from the far vertex on an edge whose primary edgeuse runs against its curve

  bugpriority: high
  tangency-labs/solidcore#1169 · Filter by author jyviko opened on Oct 26, 2026

• SMLib: a point solve on a rational surface drops a good control-net guess for a control point on the wrong part of the surface

  bugpriority: high
  tangency-labs/solidcore#1164 · Filter by author jyviko opened on Oct 26, 2026

• SMLib: a screw sweep's profile line parallel to the axis does not sweep an analytic cylinder

  bugpriority: high
  tangency-labs/solidcore#1163 · Filter by author jyviko opened on Oct 26, 2026
  1

• SMLib: screw sweep walls exceed the requested tolerance in their end spans and lie off their cylinders

  bugpriority: high
  tangency-labs/solidcore#1162 · Filter by author jyviko opened on Oct 26, 2026
  1

• fillet of a Brep::clone() fails in MergeCurveOnSurfaces (1006): clone leaves geometry unowned

  tangency-labs/solidcore#1144 · Filter by author bherbruck opened on Oct 26, 2026
  3

• SMLib: a shell's offsets meet on B-spline extensions, so a sphere shelled from its flat base gets a marched cubic rim, not the circle

  bugpriority: high
  tangency-labs/solidcore#1130 · Filter by author jyviko opened on Oct 26, 2026
  2

• SMLib: revolving an arc whose centre is within tolerance of the axis makes a sphere with no pole (off-axis pole vertex, 2.5e-6 hole)

  bugpriority: high
  tangency-labs/solidcore#1123 · Filter by author jyviko opened on Oct 26, 2026

• SMLib: a boolean's clean-up leaves edges inside one face (slits) when its merging joins their two faces

  bugpriority: high
  tangency-labs/solidcore#1120 · Filter by author jyviko opened on Oct 26, 2026

• SMLib: a sheet sweep's profile curves don't share the vertices where they meet

  bugpriority: high
  tangency-labs/solidcore#1113 · Filter by author jyviko opened on Oct 26, 2026

• SMLib: a torus rebuilt from its NURB loses a generating interval below its equator

  bugpriority: high
  tangency-labs/solidcore#1112 · Filter by author jyviko opened on Oct 26, 2026
  3

• Fillet: NxN convex corner fails on a cliff overflow's continued faces (cube corner 21/5/5)

  bugpriority: high
  tangency-labs/solidcore#1074 · Filter by author jyviko opened on Oct 26, 2026
  1

• Fillet: rounds on two opposite edges of one face, wider than half the face, build an open or unmappable body

  bugpriority: high
  tangency-labs/solidcore#1073 · Filter by author jyviko opened on Oct 26, 2026

• Fillet: a failed cliff overflow is reported as SM_FILERR_NO_ROOM

  bugpriority: high
  tangency-labs/solidcore#1071 · Filter by author jyviko opened on Oct 26, 2026
  1

• SmCone::CreateIsoCircleFromPoint builds the circle at an undefined parameter

  bugpriority: high
  tangency-labs/solidcore#1067 · Filter by author jyviko opened on Oct 26, 2026

• Local offset extends an analytic face (cylinder) approximately instead of exactly: moved boss top 2.6e-4 off

  bugpriority: high
  tangency-labs/solidcore#1061 · Filter by author jyviko opened on Oct 26, 2026
  1

• Offset Face: tangent blends on a moved face follow it (re-rounded at their size), solidcraft#3468

  bugpriority: high
  tangency-labs/solidcore#1060 · Filter by author jyviko opened on Oct 26, 2026
  1

• Surface/surface intersection does not end on the singular point where two tangent cylinders touch (bad edge, 1.2e-4 off its vertex)

  bugpriority: high
  tangency-labs/solidcore#1059 · Filter by author jyviko opened on Oct 26, 2026
  1